Bloomfield 2072 Betriebsanleitung

p/n 73674 Rev. H

PROGRAMMING - ADVANCED ACCESS THE PROGRAMMING MODE 1. Turn the brewer off with the ON/OFF Key. 2. Press and hold the 4th and 6th K

PROGRAMMING - ADVANCED (continued) TIPS FOR NAVIGATING IN THE PROGRAMMING MODE: 1. Advance through all of the Menus and wraparound to the first

10 PROGRAMMING - TABLE

11 PROGRAMMING - TABLE (continued)

PROGRAMMING - PROCEDURES Brew Settings The brew temperature cannot be set any higher than 5ºF below the Maximum Water Temperature, which is fac

PROGRAMMING - PROCEDURES (continued) Time Functions After Hours™ is an energy saving mode. When After Hours™ is activated, the E-Max™ wil

PROGRAMMING - PROCEDURES (continued) Service & Counters Machine Settings Below are the boiling points for selected North American

PROGRAMMING - PROCEDURES (continued) · “Brew Wait:” The Precise Temperature for Brewing™ feature can be overridden by setting

PROGRAMMING - PROCEDURES (continued) Factory Settings The factory settings menu can only be accessed by going into the programming mode: Press and h

PROGRAMMING - PROCEDURES (continued) Adjust Inlet Valve Time Determining Pressure and Flow NOTE: The following procedure must be performed by a

TABLE OF CONTENTS This manual applies to the following E-Max™ brewers: Decanter Brewer Models 2012 2015 2016

PROGRAMMING - PROCEDURES (continued) Calibration The probe has been factory calibrated. If a controller board is changed it is recommended that the p

PULSE BREW AND PRE-INFUSION Applications Access the Pulse Feature 1. Pre-infuse (or Pre-soak) the Bed of Coffee or Tea.

PULSE BREW AND PRE-INFUSION (continued) Pulse Feature Operation Water Outflow (Delivery)Rates The pulse feature will be activated if it h

PULSE BREW AND PRE-INFUSION (continued) Pulse Feature Examples DECANTER, THERMAL and AIRPOT MODELS 1. Pre-Infuse Standard 64 oz. Brew. Total va

. Prevent Brew Basket Overflow on 85 oz. Brew, 4 oz. of Ground Coffee. Total valve time of 236 seconds required for 85 oz. of water. Extend th

2. Extend Contact Time on Standard 3 gal. Brew. Total valve time of 319 seconds required for 128 oz. of water. Extend contact time by 65 s

TEST PROGRAM – E-Max™ Instructions for testing these system components: Entering Test Program Mode: Exiting Test Program Mode:

TEST PROGRAM – E-Max™(continued) Tea Brewers Only Decanter Brewers Only 13. By Pass Valve Off. Press ON/OFF to first turn valve on

ADDENDUM Extract from SERVICE BULLETIN 600.023 SUBJECT: Brewer Spray Disk and Gasket Application A. An revised spray disk (p/n 82727) and

NOTES RECORD SETTINGS Model: Serial No. SETTING

WARNING: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not o

Bloomfield Industries, Inc.Division of Carrier Commercial RefrigerationIn US and CanadaTelephone: 775-689-5700Fax: 888-492-2783Fax: 800-356-

OPERATION IMPORTANT: All E-Max™ brewers are tested and set at the factory. If programming adjust-ments are necessary, refer to the appropriate sec

OPERATION (continued) WARNING: Burn Hazard. This appliance dispenses very hot liquid. Serious bodily injury f

PROGRAMMING - CONTROL PANEL CONFIGURATIONS DECANTER BREWERS 1 BREW Key 1 2 BREW CANCEL Key 2 3 POWER

PROGRAMMING FEATURES AND OPTIONS 1. View Water Temperature in Tank: To view the water temperature on the screen, the brewer brewer must b

8. Clock A. Time – Battery Backup. The E-Max™ has a battery backup system which will maintain the proper time during powe

PROGRAMMING - OPERATOR LEVEL (continued) 12. View Filter Statistics: To view filter statistics, turn the brewer off. Press and hold the 1st key